Adjust Camera Orientation
Use the tripod head's Tilt, Pan, and Swivel knobs to adjust the camera orientation of the camera on the finish. You want to ensure that the green vertical line is perfectly aligned on the white finish line and that all lanes are visible in the Alignment Zone.
Adjusting Tilt
What is tilt?
Tilt is the adjustment of the camera relative to the horizon - up and down. The objective of adjusting this setting is to cover the entire width of the track.
Tilt
Figure: Camera Orientation
Aim the camera at a point approximately 2/3 of the way up the finish line and fine tune until an area comprised of the finish line plus another couple of lanes-worth above it is centered on the screen. Make sure the object of interest in both the inside and outside lanes is fully visible.
tip: Simply have someone run through the finish line and see where they appear on the screen. Adjust Tilt until competitors are clearly visible on both outside extremes of the track.
note: The area of the track covered by the camera can be changed by, Moving the camera nearer or further away from the track, and or, tilting the camera to change the field of view. Changing the value of Zoom on a zoom lens. See Optimize Lens Settings.
Adjusting Swivel
What is swivel?
Swivel
Figure: Camera Orientation
There are only two ways to be off swivel; the camera is either rotated clockwise or counter-clockwise.
Camera Off Swivel
| Lens. Sensor View. Resulting FinishLynx Image (note track color and not finish line appearing in far lanes). |
Remember our definition of swivel and think of the center line of the camera as the minute hand of a clock; the camera is either a little “past noon” or a little “before noon,” as shown in the diagram above.
note: It is the position of the sensor (entire camera) which needs to be adjusted, not just the lens.
The way to tell which way the camera is off is to pan the camera through the finish line slowly in the direction of the competitors, and watch to see which part of the image sweep goes white first:
- Top first = top of camera must be rotated away from finish line.
- Bottom First = bottom of camera must be rotated away from finish line.
This adjustment can be made in one of three ways:
- Use a camera head that has a swivel adjustment.
- Extend the tripod legs to give the effect of rotating the whole camera.
- Shim one edge of the camera body relative to the platform on which it sits.
One of the most frustrating alignment problems can occur when the camera is slightly off swivel; that is, rotated to one side or the other. The symptom of this is a picture which shows perfect alignment (white background/black lines) in some lanes and misalignment (black background/white lanes) in others; this only occurs if the camera is fairly close to being in line.
For an EtherLynx camera to be correctly aligned, the swivel must be level. This can be achieved by using a standard level from the hardware store or using the Level Indicator available as an option on EtherLynx Vision-Series of cameras.
How to use the level indicator?
- The Level Indicator displays the value of the selected camera's electronic level in real-time while the swivel is adjusted.
| Electronic Level not available. | |
|---|---|
| Not level > ±0.4 degrees | |
| Almost level > ±0.2 degrees | |
| Level < ±0.2 degrees |
How to verify the camera is level?
The camera needs to be leveled on the swivel axis while reference marks on each side of the finish line are visible in alignment mode.
For this purpose, it is advisable, whenever possible, to position narrow markers on each side of the finish line or a single vertical marker 1 or 2 meters high, in the background across the track. Such a marker, needs to be leveled and of a distinct color from the natural background.
Finish Line with 2 Alignment References seen in 1-D Alignment Mode (preferred method)
Figure: Camera Orientation
In the example above, the finish line is blue and a red narrow reference marker is set on each side of the track.
Finish Line with Single Alignment Reference seen in Alignment Mode (alternative method)
Figure: Camera Orientation
Adjusting Pan
What is pan?
Pan
Figure: Camera Orientation
Pan is the left-to-right rotational adjustment of the camera.
tip: When shooting from the outside of the track, it can be especially helpful to place something white (a piece of wood painted white works) inside of the track on a line with the finish line. This will provide a white background for the runners on the lanes furthest away from the camera.
1-d line scan mode
When the camera is panned first one way, and then the other, through the finish line, the operator will see the finish line appear on the screen as a vertical white stripe. The slower the camera is panned through the line, the wider the finish line will appear.
Adjust the Pan until the background of the track appears white and the lane lines appear black across the entire width of the track. If you have an EtherLynx 2000 OR Fusion camera, you can use the colors shown in the table below to speed up camera alignment.
Camera Alignment
| Shown below – Fusion or 2000 camera Panning left to right across the finish line Arrows indicate direction camera needs to be moved to be on the finish line. |
|---|
2-d EasyAlign mode
The final step in adjusting the camera orientation using the geared head. Turn the camera to the left or right to align the green vertical alignment line with the edge of the finish line.
Figure: Camera Orientation