Block Sensor Menu Reference
Your ReacTime Block Sensor contains four main menus:
- Training
- About
- Settings
- System (used only for operation with a ReacTime Championship False Start Detection System)
The functions for the settings in each menu and steps for how to change each setting are described in the tables below.
Training Menu
Most of the Block Sensor settings you will change are part of the Training Menu. The path for each setting begins at the Training Menu | [Sub-Menu] screen. To get there:
- From the ReacTime | Ready to Start screen, press the Menu key once.
- Press the up and down arrow keys until you arrive at the Main Menu | Training screen.
- Press the Menu key once.
- Press the up and down arrow keys until you arrive at the sub-menu in the table below. Then follow the path to change each setting.
The default for each setting appears in the last column of the table. The default settings are recommended settings. If you are not sure whether or not to change a setting, leave it at its default.
| Sub-menu | Function | Path | Default |
|---|---|---|---|
| Volume | Changes the volume of the Virtual Starter out the Loudspeaker. | Press the Menu key once. Press the up and down arrow keys to choose a number between 1 (softest) and 10 (loudest). | 7 |
| Delete Trials | Deletes all of the trials on the Block Sensor. Cannot be undone. | Press the Menu key once. Press the up arrow key once to delete all trials. | N/A |
| Photoeye | Allows configuration of the Block Sensor for use with a Photoeye. | Press the Menu key once. Press the up and down arrow keys to scroll to one of the following selections: Type, Debounce and Number. | N/A |
| Photoeye › Type | Select Norm. Open or Norm. Closed, according to your Photoeye type. | Press the Menu key once. Press the up and down arrow keys to scroll to the selection. | Norm. Open |
| Photoeye › Debounce | Allows the degree of debounce to be changed when an athlete runs through a Photoeye. | Press the Menu key once. Press the up and down arrow keys to raise or lower the debounce setting. (The minimum setting is 0.2.) | 0.3 |
| Photoeye › Number | Allows you to set the number of Photoeyes you are using with each Block Sensor. | Press the Menu key once. Use the up and down arrow keys to choose a number between 1 and 10. | 1 |
| Fire Recall | Allows you to enable the automatic “firing” of a second gun sound in the event of a false start. | Press the Menu key once. Use the up and down arrow keys to select Yes (enabled) or No (off). | No |
| Detection | Allows you to set the aggressiveness with which a false start is detected. | Press the Menu key once. Press the up and down arrow keys to set the Active Time or Threshold. | — |
| Detection › Threshold | — | Press the Menu key once. Press the arrow keys to choose Normal (recommended for most athletes) or Aggressive (recommended for lightweight athletes, such as high school girls). | Normal |
| Detection › Active Time | — | Press the Menu key once. Press the up and down arrow keys to change the amount of time an athlete may move in the blocks (from –2.0 seconds before the gun fires to a minimum of 2.0 seconds after the set command). | –0.3 From Gun |
| Gun Source | Allows you to set the source of the gun command. | Press the Menu key once. Press the up and down arrow keys to select Internal (when using the Start Button), Norm. Open or Norm. Closed (depending on your Gun Sensor type). | Internal |
| Intervals | Allows you to set minimum and maximum lengths of time between pieces of the start sequence used by the Virtual Starter feature. | Press the Menu key once. Press the up and down arrow keys to arrive at the Intervals Menu selections (Ready→Set Min, Ready→Set Max, Set→Gun Min, Set→Gun Max). | — |
| Intervals › Ready→Set Min | Allows you to set the minimum amount of time that will occur between the Virtual Starter’s Ready and Set commands. | Press the Menu key once. Use the up and down arrow to select a number (2.0 is the lowest). If you are using manually controlled intervals, hold down the down arrow until you arrive at the Manual setting. | 6.0 |
| Intervals › Ready→Set Max | — | Press the Menu key once. Press the up and down arrow keys to set the maximum amount of time between the Ready and Set commands. (2.0 seconds is the minimum.) | 8.0 |
| Intervals › Set→Gun Min | — | Press the Menu key once. Press the up and down arrow keys to set the minimum amount of time between the Set and Gun commands. (1.0 seconds is the minimum.) If you are using manually controlled intervals, hold down the down arrow until you arrive at the Manual setting. | 2.0 |
| Intervals › Set→Gun Max | — | Press the Menu key once. Press the up and down arrow keys to select the maximum number of seconds between the Set and Gun commands (1.0 seconds is the lowest). | 3.0 |
About Menu
The About Menu is not configurable. It is used to tell you what version of software (firmware) and hardware your Block Sensor is currently running.
- From the ReacTime | Ready to Start screen, press the Menu key once.
- Press the up and down arrow keys until you arrive at the Main Menu | About screen.
- Press the Menu key again. Scroll until you arrive at one of two screens telling you which version of hardware and software (firmware) you are running: About | H/W: 4.10 or About | SW: 1.20.
Settings Menu
The Settings Menu is used to change the contrast of the Block Sensor LCD and to tell you how much battery power remains.
- From the ReacTime | Ready to Start screen, press the Menu key once.
- Press the up and down arrow keys until you arrive at the Main Menu | Settings screen.
- Press the Menu key once. Scroll until you arrive at the screen you want:
- the Settings Menu | Contrast screen. Press the Menu key once. The default Contrast setting is 6. Press the up and down arrows to change the contrast (0 = dimmest, 10 = darkest).
- the Settings Menu | Battery Level screen. Press the Menu key once to see where your battery level is (100% = completely charged battery).
System Menu
The System Menu is only used with a ReacTime Championship False Start Detection System to specify the network type (Wired or Wireless) or to assign a lane number to a Block Sensor.
- From the ReacTime | Ready to Start screen, press the Menu key once.
- Press the up and down arrow keys until you arrive at the Main Menu | System screen.
- Press the Menu key once. Scroll until you arrive at the System Menu | Lane Number screen.
- Press the Menu key once. Scroll to choose the correct lane number (1-10).
- Press the Delete key once. Scroll to choose the System Menu | Network Type screen.
- Press the Menu key once. Scroll to choose the correct network type (Wired or Wireless).