Command Center Reference
Below are the most frequently asked questions about the Command Center functions and changing its settings.
How do I adjust the volume in the Starters’ Headsets?
- a. Start at the ReacTime | Ready to Arm screen. Press the Menu key once.
- b. Press the up and down arrow keys until you are at the Main Menu | System screen.
- c. Scroll until you arrive at the System Menu | Headset Volume screen.
- d. Press the Menu key once.
- e. Scroll to adjust the volume to a number between 0-10 (0=softest, 10=loudest).
How do I adjust the volume in the competitors’ Block Sensors?
- a. Start at the ReacTime | Ready to Arm screen. Press the Menu key once.
- b. Press the up and down arrow keys until you are at the Main Menu | System screen.
- c. Scroll until you arrive at the System Menu | Remote Volume screen.
- d. Press the Menu key once.
- e. Scroll to adjust the volume to a number between 0-10 (0=off, 10=loudest). This adjusts the volume on all of the Block Sensors connected to the Command Center.
How do I enable the Fire Recall setting?
The Fire Recall setting, which fires a second (internal) gun sound when a false start is detected, can be enabled by following these steps:
- a. Start at the ReacTime | Ready to Arm screen. Press the Menu key once.
- b. Press the up and down arrow keys until you are at the Main Menu | System screen.
- c. Press the Menu key once.
- d. Scroll until you are at the System Menu | Fire Recall screen.
- e. Press the Menu key once.
- f. Scroll until the screen says Fire Recall | Yes.
Why can’t I turn off my Block Sensors?
When you cannot turn off your Block Sensors, it is because the Command Center has put them into Athlete Lockout Mode to prevent competitors from tampering with the Block Sensors. To turn off the Block Sensor when it is in this mode, hold the Delete key and the Off/On key simultaneously for 5 seconds.
Why is my Wireless ReacTime Championship system not working even though all my sensors seem to be on and functioning?
If you have any extra Block Sensors that are not being used (for example, if you have 8 Block Sensors but have set up only 6), the extra Block Sensors must be OFF (or charging). If they are on and in the vicinity and have the same lane ID’s as Block Sensors in use, the system will get very confused (for example, they will think there are two lane sixes).
What is Headset Squelch and how do I change it?
Headset squelch adjusts the level of electronic noise damping in the Starters’ Headsets. Change it by doing the following:
- a. Start at the ReacTime | Ready to Arm screen. Press the Menu key once.
- b. Press the up and down arrow keys until you are at the Main Menu | System screen.
- c. Press the Menu key once.
- d. Scroll until you arrive at the System Menu | Headset Squelch screen. Press the Menu key once.
- e. Scroll until you find a comfortable level of squelch you can hear through your Headset.
I just noticed that my Command Center is set to Armed In Ready/Yes. What does this mean?
When “Armed in Ready” is set to “Yes,” data will still be captured in the event that the Starter operating the Command Center forgets to put the system into “Set” mode. The gun goes off and data is captured (without a set time).
What is the Active Time setting used for?
The Active Time default setting is –0.6 From Gun. This means that the ReacTime Championship System is set to detect a false start if there is movement equal to or less than.6 seconds before the gun. If you change the setting to a positive number (for example, 0.3 From Set), a false start will not be detected if there is movement.3 seconds after the set command is issued.
How do I change the contrast level on the LCD?
- a. Start at the ReacTime | Ready to Arm screen. Press the Menu key once.
- b. Press the up and down arrow keys until you are at the Main Menu | Settings screen.
- c. Press the Menu key once.
- d. Scroll until you are at the Settings Menu | Contrast screen.
- e. Press the Menu key once.
- f. Scroll to select the desired contrast level (0=dimmest, 10=darkest).
How do I display how much battery power I have left on my Command Center?
- a. Start at the ReacTime | Ready to Arm screen. Press the Menu key once.
- b. Press the up and down arrow keys until you are at the Main Menu | Settings screen.
- c. Scroll until you arrive at the Settings Menu | Battery Level screen.
- d. Press the Menu key once to display how much of the charge in your batteries remain (100% = fully charged Command Center).
note: The percentage of power remaining is at this time not very accurate. Block Sensors and the Command Center will run for over an hour after the LCD shows 0% remaining.
How can I tell what hardware and software versions my Command Center is running?
- a. Start at the ReacTime | Ready to Arm screen. Press the Menu key once.
- b. Press the up and down arrow keys until you are at the Main Menu | About screen.
- c. Press the Menu key once. Scroll to display the software version (S/W) or the hardware version (H/W)