Clamp the Mounting Plate to a Starting Block
ReacTime Mounting Plates secure to a range of starting block types. Starting block varieties include:
- a. U-Channel
- b. Hollow Channel
- c. Narrow Double Beam
- d. Solid Beam
- e. Moye 3 Point Stance
When clamping a ReacTime Unit to a starting block, it is most important that:
- The ReacTime Unit clamps securely to the back of the starting block
- The Block Sensor is level and therefore easy to read
- The Loudspeaker is facing toward the athlete
Keeping these points in mind, follow the instructions below:
- a. Select the starting block model pictured in the figures below that is closest to the design of your starting block. If you are mounting a ReacTime Unit to a starting block that does not require that you change the configuration of the Mounting Clamps, skip to step e.
- b. If necessary, detach the Block Sensor from the Mounting Plate by loosening the securing screw.
- c. If necessary, use a Phillips head screwdriver to remove the flathead screws from the Mounting Plate.
- d. If necessary, use the flathead screws to secure the Mounting Clamps to the Mounting Plate in the positions indicated by the clamp configuration figures below.
- e. Securely clamp the Mounting Plate to the rear of the starting block by tightening the thumbscrews.
note: These pictures do not show the Loudspeaker attached to the Mounting Plate.
- a. U-Channel
note: If you are mounting a ReacTime Unit to a U-Channel type starting block, you do not need to make any changes to the position of the Mounting Clamps as originally shipped with your ReacTime Training or Championship System.
Figure: Clamp the Mounting Plate to a Starting Block
Figure 6: U-Channel starting block
Figure: Clamp the Mounting Plate to a Starting Block
Figure 7: U-Channel Mounting Clamp configuration (as originally shipped)
Figure: Clamp the Mounting Plate to a Starting Block
Figure 8: U-Channel cross-section through Mounting Plate
- b. Hollow Channel
note: The Hollow Channel starting block does not require the use of Mounting Clamps when securing the Mounting Plate to the block. However, you must drill two holes as indicated in Figure 10 using a 7/32” drill bit. Then, you must obtain two (2) 1” x 14 oval-head, self-tapping screws to secure the Mounting Plate to the starting block.
Figure: Clamp the Mounting Plate to a Starting Block
Figure 9: Hollow Channel starting block
Figure: Clamp the Mounting Plate to a Starting Block
Figure 10: Mounting Plate holes drilled for Hollow Channel starting block
Figure: Clamp the Mounting Plate to a Starting Block
Figure 11: Hollow Channel cross-section through Mounting Plate
- c. Narrow Double Beam
note: If you are mounting a ReacTime Unit to a Narrow Double Beam type starting block, you do not need to make any changes to the position of the Mounting Clamps as originally shipped with your ReacTime Training or Championship System.
Figure 12: Narrow Double Beam starting block
Figure: Clamp the Mounting Plate to a Starting Block
Figure 13: Narrow Double Beam Mounting Clamp configuration (as originally shipped)
Figure: Clamp the Mounting Plate to a Starting Block
Figure 14: Narrow Double Beam through Mounting Plate
- d. Solid Beam
note: For the Mounting Clamp configuration used with this type of starting block, you need to use 2” x ¼”-20 hex-head bolts instead of the thumbscrews originally included with your ReacTime Training or Championship System.
Figure: Clamp the Mounting Plate to a Starting Block
Figure 15: Solid Beam starting block sample
Figure: Clamp the Mounting Plate to a Starting Block
Figure 16: Solid Beam Mounting Clamp configuration
Figure: Clamp the Mounting Plate to a Starting Block
Figure 17: Solid Beam cross-section through Mounting Plate
Reminder: Replace the thumbscrews with 2” x ¼”-20 hex-head bolts.
- e. Moye 3 Point Stance
Figure: Clamp the Mounting Plate to a Starting Block
Figure 18: Moye 3 Point Stance starting block
Figure: Clamp the Mounting Plate to a Starting Block
Figure 19: Moye 3 Point Stance Mounting Clamp configuration
Figure: Clamp the Mounting Plate to a Starting Block
Figure 20: Moye 3 Point Stance through Mounting Plate