(Optional) Use a Single or Multiple Photoeyes
With each ReacTime Training System, you may train with as many as 10 Photoeyes. Follow the instructions in this section to do the following:
- a. Set up a Photoeye
- b. Connect multiple Photoeyes together
- c. Change Block Sensor settings
- a. Set up a Photoeye
- a. Choose a place on the track where you want to record the athlete’s time out of the starting blocks to the first beam break. (For example, the 10-meter mark.)
- b. Unfold both Photoeye tripods, extending the legs so that the top of each tripod is as high as the athlete’s torso.
- c. Lock the legs by flipping the levers at the feet of the tripod.
- d. Place the tripod with the reflector on one side of the lane, with the front of the reflector facing the Photoeye tripod.
- e. Place the tripod with the Photoeye on the other side of the lane, facing the reflector tripod. Make sure each tripod is at approximately the same height.
- f. Connect the extra Signal Input Cable that came with the Photoeye to the Photoeye Cable. (You are already using the Signal Input Cable that came with your ReacTime Training System for the Start Button or Gun Sensor.)
note: You may extend the Photoeye Cable by connecting it to a standard Lynx Gun Cable or to any 3-pin XLR cable.
- g. Connect the other end of the Signal Input Cable to the Block Sensor Photoeye input (see Figure 22).
- h. Angle the Photoeye toward the reflector until the red light on the side of the Photoeye appears constant.
- i. Have someone run through the beam once. Watch to see that the red light turns off briefly that person breaks the beam. Your Photoeye is now properly set up. If you are using more than one Photoeye, go to b. Otherwise, go directly to c.
- b. Connect multiple Photoeyes together
If you are using more than one Photoeye with your ReacTime Training System, you need to use a Y Splitter Cable to connect the Photoeyes together.
- a. Connect each female end of the Y Splitter Cable to each Photoeye Cable.
- b. Connect the Signal Input Cable to the male end of the Y Splitter Cable.
- c. Connect the open end of the Signal Input Cable to the Block Sensor Photoeye input.
note: If you are working with two athletes, it is recommended that you leave one lane of length in between each athlete so that you have enough room for the Photoeye tripod setup. For example, train your athletes out of lanes two and four, leaving lane three open.
- c. Change Block Sensor settings
When you are using the ReacTime Training System and one or more Photoeyes, you must configure the Photoeye menu on the Block Sensor. Follow these instructions:
- a. At the Main Menu | Training screen, press the Menu key.
- b. Scroll through the Training Menu sub-menus using the up or down arrow keys until you arrive at the Training Menu | Photoeye screen. Press the Menu key once.
- c. Scroll through the Photoeye sub-menus until you arrive at the Photoeye Menu | Type screen. Press the Menu key once.
- d. Scroll to choose Type | Norm. Open or Norm. Closed. (Note: If you are using a Lynx Photoeye, Normally Open is the correct type.) After making your selection, press the Delete key once.
- e. Scroll through the Photoeye sub-menus using the up or down arrow keys until you arrive at the Photoeye Menu | Number screen. Press the Menu key once.
- f. Use the up and down arrow keys to set the number of Photoeyes you are training with (between 1-10).
- g. Press the Menu key once to arrive back at the ReacTime | Ready to Start screen.
Now you are ready to practice starts using your ReacTime Training System with one or more Photoeyes. The Block Sensor LCD lists in the lower right corner the time it took the athlete to travel from the starting block to the first beam break. If you are using more than one Photoeye, all of the beam breaks are shown in a paging, sequential display in the LCD’s lower right corner (see Figure 28). Each number represents the time it took the athlete to travel from the starting blocks to the corresponding beam break.
Figure: (Optional) Use a Single or Multiple Photoeyes
Figure 28: LCD showing a beam break reading
- 1--2.622 = first beam break value