ReacTime Training 1.30
May 15, 2007
These notes cover the updates to the ReacTime Training Software 1.30 since version 1.20. For mounting and configuring the block sensors and basic use of the software, see the ReacTime Training Setup QSG, the ReacTime manual, or the software's own help (Help | Contents).
Ability to Overlay Traces
ReacTime Training software now features an Overlay Mode, which allows you to compare up to twelve traces by overlaying them. You can also remove individual traces from the overlay, as you like.
Working in Overlay Mode
By default, ReacTime Training Software's Overlay Mode is turned off.
To turn on Overlay Mode:
- Make sure that you have a workout open.
- Click the Overlay Mode icon (a chart with a green dot). The icon becomes two different icons:
- the chart with a red dot disables Overlay Mode, and
- the chart with an eraser allows you to clear a trace overlay after clicking on it.
Notes about Overlay Mode
Note the following when you are in Overlay Mode:
- Any traces that you click on in the Results Zone are displayed without erasing what is already there.
- Each trace is a different color.
- A legend to the right of the traces display allows you to keep track of traces and their corresponding colors.
- You can select a maximum of 12 traces to be overlaid.
- You can remove a single trace from the overlay.
- Each time you turn Overlay Mode either on or off, all of the traces are cleared from the Chart Zone.
Practice Using Overlay Mode with the Sample Workout
Follow these instructions to see how ReacTime Training's new Overlay Mode works.
- After running the ReacTime Training software, click File from the Menu bar and then select Open.... An Open dialog appears.
- Double-click MondaysWorkout.rtw. A workout with three participants opens. The trace for Maddie Rhodes appears in the Chart Zone.
- Click the Overlay Mode icon. Maddie Rhodes' trace disappears from the Chart Zone.
- Triple-click Trial 1, next to Carter Rhodes' name in the Results Zone. Carter Rhodes' trace appears in black bold in the Chart Zone.
- Note: To display a trace, you must click in the corresponding Trial box. Clicking an athlete's First Name or Last Name field does not display a trace.
- Triple-click Trial 2, next to Harry Norton's name. Harry Norton's trace appears in bold blue in the Chart Zone.
- Triple-click Trial 3, next to Maddie Rhodes' name. Maddie Rhodes' trace appears in bold green in the Chart Zone. To the upper right of the overlaid traces is a legend telling you which color trace corresponds with which trial.
note: Triple-click a trial again to remove the individual trace it corresponds to.
New Serial Options
Ability to Add Multiple Serial Ports
ReacTime Training Software can now be configured to work with multiple serial ports, allowing you to accommodate multiple Block Sensors.
note: If your computer does not have a serial COM port, you may use a USB to serial port converter. Using additional USB to serial port converters allows you to increase the number of COM ports. USB to serial port converters are available for purchase from Lynx System Developers, Inc.
To add serial ports:
- Click Hardware from the Menu bar and then select Options.... An Options dialog appears.
- Click the New button. A Serial Port is added to the text box, with the status "Not Running."
- Type a name for each unique block sensor in the Name: text box.
- Note: This name appears in the Results Zone, so you can tell which source a trace came from. It is important that you follow this step to name each COM port.
- From the Serial Port: drop-down list, select the COM port that you are configuring. The Baud, Data Bits, Stop Bits, and Parity settings are configured automatically.
- When you are finished, either click New to continue adding COM ports, or click Ok to exit this dialog.
Ability to Turn Off Prompting Traces
You can now configure ReacTime Training Software to download traces automatically, rather than being prompted each time.
- Click Hardware from the Menu bar and then select Options.... The Options dialog appears.
- Uncheck the Prompt to select a trace to download checkbox.
- Click Ok to exit the dialog.
note: If prompting traces is disabled, the most recently run trial is the trace that is downloaded automatically.
Ability to Add Trace Downloads to an Overlay
You can now download a trace directly into an overlay.
- Click Hardware from the Menu bar and then select Options.... The Options dialog appears.
- Near the bottom of the dialog, check the Add trace downloads to the overlay box.
- Click Ok to exit the dialog.
Other New Features
Download Reaction Times and Trace Data Separately
ReacTime Training Software 1.30 lets you download reaction times and trace data independently, using two separate icons.
note: The new icons described below replace the previous Add Trial icon in ReacTime Training Software 1.20.
- To download reaction times only: with a workout open, click the green reaction-times icon (it shows a 0.131 readout). Reaction times for your workout are loaded into the Results Zone.
- To download trace data only: with a workout open, click the yellow trace icon. Traces for your workout are loaded into the Chart Zone.
note: If you download trace data before reaction times, the reaction times are automatically downloaded before the trace data.
Ability to Display a Power Line on a Trace
ReacTime Training can now display a line indicating the power with which the athlete left the blocks. The Show/Hide Power Line button above the Chart Zone turns it on and off; while the power line is on, the button's icon shows a horizontal line across the trace.
Ability to Write a Comma Delimited File
The ReacTime Training Software now writes a comma delimited text file every time you save a workout.
- The file is saved as
*.RIT. - You can also save an in-progress workout to an
*.RITfile by clicking File from the Menu bar and then selecting Save RIT.
The .RIT File Format
The fields of each line in a *.RIT file are:
Trial#,LastName,FirstName,ReactionTime,Source,Power,Time To Distance,Time To Distance - ReactionTime,"break 1 (diff), break 2 (diff), ...Sourceis the name given to the serial port. You can assign a unique name to each source in Hardware | Options (see Ability to Add Multiple Serial Ports, above).Time To Distanceis the time to the last photoeye break.Time To Distance - ReactionTimeis the time to the last photoeye break minus the reaction time.breakis a photoeye break.(diff)is the difference in time between this photoeye break and the previous one.
The first lines of the sample .RIT file shown in the release notes:
0,0,0
1,Smith,Emmit,,0.774,Lynx 1,10573,14.728,13.954,
2,Glance,Harvey,,0.448,Lynx 9,40881,No Time, No Time,
3,McTear,Houston,,0.323,Lynx 1,4722,17.051,16.728,