Computer and IT readiness checklist

Give this checklist to whoever sets up your timing computers. Everything here should be done before the first meet.

How to fix it

The computer

  • A Windows computer. FinishLynx does not run on macOS (Known limitations).
  • Recommended: Windows 10 or later, 2 GHz Core i7 or faster, 8 GB RAM or more, 512 GB SSD or more, a wired Ethernet (RJ45) port and two or more USB ports.
    • The manual's minimums are far lower (500 MHz, 512 MB RAM, 16 GB storage, 10/100 Ethernet, one USB port), so a current laptop that falls short of the recommendation still runs FinishLynx. See Computer requirements.
  • One computer is required and two are recommended, so meet management runs on its own computer.
  • No Ethernet port? Use a USB Ethernet adapter and give it the static IP address below.
  • A computer the timing staff control. Managed school computers can stop LynxPad from saving reports, and security software or IT policies may block the installers.

Installing the software

  • Administrator rights to run the FinishLynx, plug-in and LynxPad installers.
  • FinishLynx and all plug-ins installed in the same folder (C:\Lynx is recommended).
  • FinishLynx run as administrator (right-click the shortcut, Properties, Compatibility tab, Run this program as an administrator).
  • LynxPad run as administrator every time it starts, not only when it is installed.

Network settings

  • A static IP address on the wired Ethernet adapter used for the cameras: 192.168.0.5, subnet mask 255.255.255.0.
  • The addresses just above it (192.168.0.6, 192.168.0.7 and so on) kept free: FinishLynx gives them to the cameras.
  • Other timing computers: evaluate computer 192.168.0.15, meet management computer 192.168.0.90.
  • Best practice is a separate, isolated network for the timing equipment. If it must share a managed network, open UDP ports 45780 (camera boot) and 41925 (camera communication): see School or Managed Network.
  • Wi-Fi off while the cameras boot. Wi-Fi can be used after the cameras have loaded if it is on a different subnet from the camera network.
    • Lynx recommends keeping Wi-Fi off on timing laptops if possible, and doing internet work (live results, meet management) on a separate computer.
  • If the computer also uses Wi-Fi or a second adapter for internet, set File | Options | General, Camera Network, to the IP address of the camera adapter (192.168.0.5).

Firewall and security software

  • Allow FinishLynx (C:\Lynx\Lynx.exe) through Windows Defender Firewall for both Private and Public: Windows Security | Firewall & network protection | Allow an app through firewall | Change settings | Allow another app, select C:\Lynx\Lynx.exe, and check both columns.
    • Check it again after a Windows update, which can clear the rule.
  • If other security software is installed (Avast and others), allow C:\Lynx\Lynx.exe in it too.
    • If a camera still only boots with that program's firewall off, keep it off on the timing computer: the manual recommends disabling third-party firewall and antivirus tools there because they can block the camera traffic.

Sharing between timing computers

  • Same Workgroup, not joined to a Domain.
  • Network Discovery and File and Printer Sharing turned on, and the meet folder shared with read and write access, as in the Windows 11 networking guide.
  • On the capture computer, C:\Lynx\Temp shared with read and write access.
  • See Multi-computer networking for the full steps.

Student and athlete data

  • FinishLynx has no athlete accounts and sends nothing to Lynx. It stores only what the meet software gives it (names, teams and lanes in the start-list files) and the results and image files it writes, all in folders on your computers.

Windows 11 printing

  • On Windows 11, FinishLynx can stop responding when you print. Apply the Windows 11 print fix on every timing laptop before the first meet.
    • Add a DWORD named PreferLegacyPrintDialog with a value of 1 under HKEY_CURRENT_USER\Software\Microsoft\Print\UnifiedPrintDialog. The steps and a video are in Slow start or printer warning.

Related resources