Decoder settings
Every chip system connects to FinishLynx through the LapTime plug-in: the meet manager sends start lists with ID numbers to FinishLynx, the chip system sends IDs and times, FinishLynx matches them, and the meet manager loads the results. Set up the LapTime device first, then use the settings for your system.
How to fix it
Set up the LapTime device
- Click Help | About and check that the LapTime plug-in is listed with a serial number.
- It installs separately from the Plugins section of the Software page, activated with its own serial.
- Network readers set up with the MYLAPS and IPICO guides also use the Network COM Port, which is built into FinishLynx 13.00 and later.
- Put the decoder and the FinishLynx computer on the same network subnet (the first three numbers of the IP address match).
- Click LapTime | Options…, click New, choose your device, and set the Serial Port (the COM port or network connection your decoder uses).
- Close and restart FinishLynx, then check that the device status in LapTime | Options… reads Running.
Settings by decoder
- MYLAPS BibTag or ProChip (through MYLAPS Timing & Scoring)
- Connection: add a TCP/IP Export in Timing & Scoring. If Timing & Scoring runs on a different PC, enter the FinishLynx PC's IP address in the exporter.
- Hidden settings: FillInTime, IdMaxSize, IdStripZeros, TotalLaps and IntSyncMask. See Reads arrive but no marks, or the chip time card and MYLAPS BibTags card.
- Sync: Sync. Source = None when the camera and decoder are both on GPS. Internal plus a gunshot on the decoder when the camera has no GPS; the gunshot only lines up the clocks and doesn't need to match the real gun time.
- MYLAPS Cloud Timing: use the latest Timing & Scoring (version 2.15 or later), which connects to Cloud Timing. FinishLynx still connects to Timing & Scoring over the TCP/IP Export, not to Cloud Timing directly. Questions about Cloud Timing itself go to MYLAPS.
- Guides: MYLAPS Timing & Scoring QSG, MYLAPS Timing & Scoring Video QSG, MYLAPS BibTag QSG, MYLAPS partner page
- IPICO Lite or Elite reader
- Connection: Ethernet. Change the reader's IP address from its factory default (10.19.1.51 on the Lite, 10.19.1.101 on the Elite) to one on your FinishLynx network, for example 192.168.0.151.
- Port: 10000 (every read; recommended). Port 10200 is only for the IPICO First Seen / Last Seen suffix hidden setting; with Last Seen, also set the Start Mask to 0.0.
- Final Split: Official Time.
- Guides: IPICO Lite QSG, IPICO Elite QSG, Integrate IPICO RFID Readers with FinishLynx LapTime
- Trident
- Setup: follow the IPICO video, with two changes.
- Port: 10001 (IPICO uses 10000).
- Final Split: LapTime (IPICO uses Official Time).
- Guide: Trident's own FinishLynx setup information covers the reader side. For a cross-country meet with Trident, see Cross-country workflow.
- Race Result
- Guide: follow Race Result's knowledge-base article on connecting to FinishLynx. The FinishLynx side is the LapTime device above.
- Other readers
- Before you buy, confirm the maker documents a FinishLynx LapTime connection, then follow their guide.
- The chip system normally doesn't talk to the meet manager at all. If you want it connected straight to MeetPro or another meet manager with no FinishLynx in between, confirm that with the meet manager's maker.
- Reader makers can integrate using the Lynx LapTime Protocol, which defines the data FinishLynx expects from a chip system.
Questions about the decoder or its own software go to the chip-system vendor. For the FinishLynx side, see LapTime Configuration and the LapTime Module section of the manual.
Good to know
Final Split (LapTime | Options…) sets where the last split time comes from: Official time lets the EtherLynx camera's time override the decoder's, and LapTime keeps the decoder's time.
Good to know
MYLAPS side antennas and a mat can share one portable decoder, limited only by its antenna connectors. MYLAPS recommends keeping side antennas about 5 m from any other signal source, including the EasyMat, so check that spacing works at your finish line first.
Related resources
- MYLAPS Timing & Scoring QSG — Guide · PDF
- MYLAPS BibTag QSG — Guide · PDF
- IPICO Lite QSG — Guide · PDF
- IPICO Elite QSG — Guide · PDF
- Lynx LapTime Protocol — Guide · PDF