Reads arrive but no marks
Your decoder is sending reads, but nothing marks the image or fills in the results. The connection is usually fine and a LapTime setting is holding the reads back: confirm FinishLynx is receiving them, then work through the settings below in order.
How to fix it
Confirm FinishLynx is receiving reads
- Look at the status bar at the bottom left of FinishLynx.
- LapTime: Received # means FinishLynx is connected and counting reads.
- NOT CONNECTED means the connection is not open. Check the port and network settings in Decoder settings.
- Click LapTime | Options… and check the status of your device.
- Not loaded: close and restart FinishLynx (a new LapTime device needs a restart).
- Not Running: no Serial Port is selected for the device.
- Not Connected: a network port is set, but the connection to the decoder isn't established.
- Running: FinishLynx is sending or listening through the selected port.
- Click Help | About and check that the LapTime plug-in is listed. Without it, the only LapTime device available is From Image.
Give the event a start
LapTime ignores every read that arrives before the start, and for the Start Mask time after it (3.0 seconds by default). The mask keeps stray reads around the start from counting, but it also means a test with no start shows nothing.
- Give the event a start before you pass a chip over the mat, for example Event | Manual Start, then the Space Bar.
- For a test, you can instead clear the Start Mask field in LapTime | Options… and try again.
- Set it back to 3.0 seconds before you time a race, so stray reads around the start are still ignored.
MYLAPS: set the hidden LapTime settings
Some settings for MYLAPS Timing & Scoring are only in the hidden settings (page 2 of the MYLAPS Timing & Scoring QSG). A missing IntSyncMask has caused this problem.
- Hold Ctrl+Shift and click File | Options… to open the Other (hidden) settings.
- Under LapTime, set LapTime\FillInTime to 2 and LapTime\TotalLaps to the total number of splits (1 for a single finish decoder).
- For BibTags, also set LapTime\IdMaxSize to 5, LapTime\IdStripZeros to 1 and LapTime\IntSyncMask to 2 (when the camera is not synced to GPS).
- Click OK.
- What each setting does is on the chip time card and the MYLAPS BibTags card of the FinishLynx Other Settings page.
MYLAPS: sync the decoder with FinishLynx
- Camera and decoder both synced to GPS: set Sync. Source to None in LapTime | Options….
- Camera not synced to GPS: set Sync. Source to Internal, then trigger a gunshot on the decoder while FinishLynx is running and connected to Timing & Scoring.
- The gunshot only lines up the chip-read times with FinishLynx. It does not start the race clock, so it doesn't need to match the real gun time.
- Do it again every time FinishLynx is restarted. Best practice is a gunshot at the start of every race; the status bar shows NOT SYNCED until it is done.
- A gunshot received late (for example, by replaying data) gives the wrong sync.
Keep the chip map file on the FinishLynx computer
- If LapTime reads its map file over the network from another computer (for example, the meet-management laptop), copy the file to the FinishLynx computer.
- When that share stops responding, chip numbers stop appearing. A local copy means a network drop can't stop the reads.
- In LapTime | Options…, point Map File at the local copy.
- Before the first race, check that the status bar shows LapTime: Received # and pass a test chip over the mat.
- If the read shows only the chip code, check that the codes in the map file are typed exactly as FinishLynx receives them. Compare with the code a test read shows: if the received code has no dashes or spaces, remove them from the map file.
Remove old LapTime devices
- On a system you inherited or reused, check LapTime | Options… for devices or connections left from an earlier setup.
- Delete any you no longer use, then restart FinishLynx. A deleted device stays listed until you restart.
If reads show only a bib and time, with no names
- The chip map links each chip to a bib, and the meet manager's .ppl file links each bib to a name. You don't need to edit the chip file.
- Update the start lists in your meet manager so it writes its .sch, .evt and .ppl files.
- Point the FinishLynx Input Directory (File | Options | Database tab) at the folder where the meet manager writes them. See Start lists not found.
- Open the seeded event from the schedule instead of a blank event. A blank event (File | New) saves a .lif with no event number, so the meet software reports that the results file is not found.
Check these
- The event's Laps is set before any reads arrive (1 for a finish-only decoder).
- The Results fields Cumulative Split Time, Last Split Time and Laps are turned on (File | Options | Results tab).
- A color is selected for Splits under Show Lines, so reads show as lines on the image. See Overlays or labels missing.
- The Results: Key in LapTime | Options… is the field your chips map to (ID when you use bib numbers).
- If Create results is unchecked, reads for any key that isn't in the start list are ignored.
Setting up the plug-in for the first time? Start with Decoder settings. The reference is MYLAPS in the FinishLynx manual, the MYLAPS Timing & Scoring QSG and LapTime Configuration.
Related resources
- MYLAPS Timing & Scoring QSG — Guide · PDF