Flashing amber BOOT light

A flashing amber BOOT light means the camera has booted and is waiting for FinishLynx: a slow blink while it searches for the software, a fast blink while it loads. The light alternates yellow and red, so it can look like blinking red.

A camera stuck here is almost always held up by the timing computer, not a camera fault, and it is the usual result on a new or replaced computer. Start with the FinishLynx settings and work down the list in order; the Camera Boot Troubleshooting Guide covers the same steps.

How to fix it

Check the FinishLynx settings

  1. Go to File | Options | General tab and set Hardware Type to Detect
    • If the Hardware Control window says "Not looking for hardware", Hardware Type is set to None
    • Ethernet also works for EtherLynx and IdentiLynx cameras
  2. Set Camera Network to the static address of the camera adapter (192.168.0.5 on the standard setup)
    • Camera Network is a drop-down list of this computer's adapter addresses, so you can't type in it. If your static address isn't listed yet, set it in Windows (next section), then reopen FinishLynx and pick it
  3. Click OK, restart FinishLynx and reboot the camera

Give the camera adapter a static IP address

  1. Right-click the Start button, choose Settings, then Network & internet | Ethernet (the adapter the camera is plugged into)
  2. Next to IP assignment, click Edit and choose Manual
  3. Turn IPv4 on, enter IP address 192.168.0.5 and subnet mask 255.255.255.0, and click Save. The Windows 11 networking guide shows the same steps
    • The address is set in Windows, not in FinishLynx. Another static address also works; FinishLynx gives the camera the next address up (192.168.0.6 when the computer is 192.168.0.5)
    • On a laptop with no Ethernet port, use a USB or USB-C Ethernet adapter and set the static address on that adapter
    • On Windows 10, it's in Network and Sharing Center | Change adapter settings: right-click the adapter, choose Properties, then Internet Protocol Version 4 (TCP/IPv4) | Properties (Windows 10 networking guide)

Turn Wi-Fi off while the cameras boot

  1. In Settings | Network & internet, turn Wi-Fi Off
    • Wi-Fi can be used after the cameras have loaded if it's on a different subnet from the camera network
    • Lynx recommends keeping Wi-Fi off on timing laptops if possible, and doing internet work (live results, meet management) on a separate computer

Allow FinishLynx through the firewall

  1. Open Windows Security | Firewall & network protection | Allow an app through firewall and click Change settings
  2. If Lynx is in the list, check its far-left box and both the Private and Public columns, then click OK
  3. If it isn't, click Allow another app..., browse to C:\Lynx\Lynx.exe and add it, then check the far-left box and the Private and Public columns and click OK
  4. If Lynx.exe is allowed only in the outbound rules, add an inbound rule for it as well (Windows Defender Firewall | Advanced settings | Inbound Rules)
  5. A third-party firewall or antivirus (Avast, for example) has to trust the camera network too. Allowing Lynx.exe isn't enough if it treats that network as public or untrusted
  6. Check this again after a Windows update, even if it was set before. An update can clear the permission
    • If your IT department manages the firewall, they can instead open UDP port 45780 (camera boot) and UDP port 41925 (camera communication after boot). Everything IT needs is in Computer and IT readiness checklist

Turn off power saving on the adapter

  1. Open Device Manager | Network adapters, right-click your Ethernet adapter and choose Properties
  2. On the Advanced tab, set Energy Efficient Ethernet to Disabled
  3. On the Power Management tab, uncheck "Allow the computer to turn off this device to save power"
  4. With a USB-to-Ethernet adapter, also uncheck that box on each USB Root Hub under Universal Serial Bus controllers

Run FinishLynx as administrator

  1. Right-click the FinishLynx shortcut and choose Properties
  2. On the Compatibility tab, check Run this program as an administrator and click OK

If the camera still won't load

  • Swap the Ethernet cables one at a time, and try a different PoE injector or switch port
  • Install any pending Windows updates and restart the computer
  • Make sure no other device on the network uses the camera's address (one above the computer's: 192.168.0.6 for the first camera)
  • On a long cable run, test with a short cable straight from the camera to the PoE injector and the computer. If it loads that way, the run is the problem
  • Copper network cable is good for about 100 m (around 300 ft). Beyond that, use fiber with a media converter at each end: see Choosing a cable
  • FinishLynx shows Error 202 while loading the camera: see Error 202
  • FinishLynx shows "Error Aligning a Camera": no camera has loaded yet. Boot the camera before opening alignment mode
  • After all of that, Lynx support can connect to the computer remotely and check the settings with you. Install TeamViewer first, then use the button below

Good to know

Camera settings don't carry over to a new computer. The camera loads with default settings, so check Camera Settings (such as Automatic Capture) once it boots.

Talk to Lynx Support

Tell the team what you’re seeing and what you’ve already tried. They’ll follow up by email or phone.

Contact Support

Related resources