HyTek
FinishLynx and HyTek Meet Manager share one folder: Meet Manager writes the start lists into it, and FinishLynx reads them and writes each race's .lif results file back to it. Results don't flow into Meet Manager by themselves: you save the race in FinishLynx, then click Get Times in Meet Manager.
On two computers, keep the folder on the FinishLynx computer and map it as a network drive on the HyTek computer, so a network drop doesn't cut FinishLynx off from its files. The video Tutorial: Integrate FinishLynx with Hy-Tek Meet Manager shows the setup.
How to fix it
Set up the FinishLynx interface in Meet Manager
- One-time setup: in Meet Manager go to Run, then Interfaces | Setup | Photo Finish, select FinishLynx File Sharing and click OK.
- Go to Interfaces | Photo Finish - FinishLynx File Sharing Mode | Update Start Lists.
- In the Update Start Lists dialog, select the session (or All Events) and check Activate update of start lists.
- Click Change Data Location and set it to the shared folder both computers can access. The dialog shows the current folder next to Shared Location for FinishLynx Data.
- Click OK. Meet Manager writes three files into that folder: lynx.sch (order of events), lynx.evt (events, heats and athletes in lanes) and lynx.ppl (bib numbers linked to names and teams).
- From then on the start lists update whenever you seed or re-seed an event. If you switch two runners in a heat from the Run menu, press Ctrl-U to update the start lists.
Set the FinishLynx directories
- In FinishLynx, go to File | Options and click the Database tab.
- Set Data Source to Files, and set both the Input Directory and Output Directory to the same shared folder. Most setups also point the Event Directory there.
- Check it is the same folder Meet Manager uses. Many computers have more than one tfmeets folder, and pointing at the wrong one is the most common cause of missing start lists and results.
- Sharing and mapping the folder is in the Windows 11 networking guide and Multi-computer networking.
Load the schedule
- In FinishLynx, go to File | Goto Event and click Load Schedule. The events from the lynx.evt file appear in the drop-down list.
- Open the event from the list rather than a blank File | New event.
- A blank event saves a .lif named only by a timestamp, with no event number, and Meet Manager then reports "Results file for event #, heat 1 not found" even though a .lif is in the folder.
Get the times in Meet Manager
- Save the event in FinishLynx.
- In Meet Manager go to Run, select the event and heat, and click Get Times (F3).
- If you corrected the race in FinishLynx after getting times, save it again and click Get Times again.
If it didn't work
- Start lists are not available until at least one event has been seeded in Meet Manager.
- If the schedule doesn't load, or events load with no athletes, see Start lists not found.
- If Get Times brings results into Meet Manager in tenths instead of hundredths, see Times rounded to tenths.
Three-computer setups (capture, evaluate and HyTek)
- Give each computer a fixed IP on the same network, for example capture 192.168.0.5, evaluate 192.168.0.15 and HyTek 192.168.0.90.
- Keep the shared folder on the capture computer, share it with read/write access, map it as a network drive on the other two, and point all directories at it.
- Also share
C:\Lynx\Tempon the capture computer so the evaluate computer can see race images. See Capture-and-read FinishLynx setup.
For cross country with chips, HyTek's CC/RR module uses the same file-sharing interface. Settings inside Meet Manager itself are HyTek's software: their own pages are HY-TEK File Sharing Setup for FinishLynx and Getting Results from FinishLynx.
Related resources
- Tutorial: Integrate FinishLynx with Hy-Tek Meet Manager — Video · YouTube
- Windows 11 networking guide — Guide · PDF
- HY-TEK File Sharing Setup for FinishLynx — Link
- Getting Results from FinishLynx — Link