Initial connection
The Lynx Wind Gauge (WG-Lynx) plugs into the back panel of a Vision-series camera and sends each wind reading straight into FinishLynx. Have the camera set up and loaded in FinishLynx first, using the QSG for your camera package from the Quick Start Guides page.
The same steps are in the Lynx Wind Gauge QSG. A SeriaLynx connection and a wind reading on a display board are covered further down.
How to fix it
Connect the wind gauge
- Place the wind gauge on top of its tripod.
- Connect the male end of the supplied 200 foot XLR extension cable to the XLR port on the gauge.
- Connect the female end of the XLR cable to the Wind Gauge Input Cable.
- Connect the Wind Gauge Input Cable to the camera's back panel.
- The serial connector goes in the SERIAL port.
- The power leads go in the color-coded red and black 12VDC ports.
- Check for power: the red light next to the XLR port on the gauge starts to blink.
Set up the Wind tab in FinishLynx
- Start FinishLynx and go to File | Options, Wind tab.
- Set Wind Module to Lynx and Serial Port to
<camera name> (Body).- On a Connection Box, the port is
<camera name> (C-Box).
- On a Connection Box, the port is
- Check the serial settings: 9600 baud, 8 data bits, no parity, 1 stop bit.
- Leave Default Mode at 100M (Start 0.0, Duration 10.0) and Warn If Offline on.
- The other modes and what each setting does are on the manual's Wind Gauge options page.
- Click OK, then close and reopen FinishLynx. The Wind Module change only takes effect on the next start.
Test the wind reading
- Open a new race for testing.
- Start it with a start sensor or a manual start.
- After about 10 seconds the wind reading appears in the Wind line of the Information Zone.
If a RadioLynx is already on the camera
- On a Vision camera, the RadioLynx uses its own RADIO LYNX port, so the SERIAL port stays free for the wind gauge.
- On other cameras, use a spare serial port on the Connection Box.
Connecting through a SeriaLynx
- In the Wind tab, set Serial Port to Network (connect), not Network (listen), and enter the IP address and port (10001 or 10002) labeled on the SeriaLynx.
- This is the manual's SeriaLynx procedure. The Network options are built into FinishLynx 13.00 and later.
- On the SeriaLynx dashboard, set that serial port to 9600 baud, 8 data bits, no parity and 1 stop bit.
- Power the gauge separately. The Wind Gauge Input Cable takes its power from the camera's 12 V ports, so a gauge on a SeriaLynx needs its own DC power supply.
- If your adapter has no power connection, Lynx can supply the wiring: use the button below.
If the gauge shows no light, or a solid red light, see No light, solid red light or stopped after a fall.
Showing the wind reading on a display board
- The reading reaches a board only through a scoreboard script that sends it, so it depends on the board. Set the script up as its own entry in Scoreboard | Options…, as in Connecting a new scoreboard.
- The Scoreboard scripts page has wind scripts for the MicroTab (MicroTab LED – Wind, uTabLED_Wind.lss), Microgate uGraph boards and a Gill wind-only display (GillWind.lss).
- A board with no wind script can't show the wind. On a video board, ResulTV can: see Wind colors, foul/valid images and custom colors.
Good to know
You can't take the gauge's raw live wind feed out for your own display: see no raw live wind feed. FinishLynx sends each race's reading instead.
Talk to Lynx Support
Tell the team what you’re seeing and what you’ve already tried. They’ll follow up by email or phone.
Related resources
- Lynx Quick Start Guides — Quick start guides
- Lynx Wind Gauge QSG — Guide · PDF