LED scoreboard (All Sport 5000)

FinishLynx drives a Daktronics All Sport 5000 console over a serial cable with the Powertime.lss script, and the console runs the football or track scoreboard. HyTek Meet Manager can't send to this board: the clock and results come from FinishLynx, and HyTek only trades files with the FinishLynx computer.

Not sure this is your board? See Which Daktronics setup do I have.

How to fix it

Set the console

  1. Enter code 8602 on the All Sport 5000 (insert LL-2439). It is the code for a USB-to-serial adapter on the FinishLynx computer.
  2. Connect the computer's USB-to-serial adapter to the console with the 9-pin to 25-pin serial cable (J6 on the console).

Set up FinishLynx

  1. Go to Scoreboard | Options, click the Scoreboard tab, then click New.
  2. Set up the entry as follows:
    • Script: Powertime.lss
    • Name: Football/Track Scoreboard
    • Code Set: Single Byte
    • Serial Port: the COM port the adapter is on (Device Manager shows its number)
    • Baud 9600, Data Bits 7, Parity Even, Stop Bits 1.0
    • Running Time: Normal
    • Results: Auto, with Always send place enabled
    • Paging enabled, Size 1, Time 5.0
  3. Click OK.
  4. Restart FinishLynx to load the scoreboard script.
  5. To show only the running clock, set Results to Off instead of Auto.

If the clock doesn't run on the board

  • Check the code entered on the All Sport 5000 is 8602, not 6802. The digits are easy to swap. The code comes from Daktronics' documentation, so questions about other codes (such as 8604, FlashTiming's code) are for Daktronics.
  • Check the All Sport's software revision is above V1.4.
  • Check Serial Port is the COM port the All Sport 5000 cable is on, and that no other FinishLynx option (such as the capture button, usually COM1) uses it.
  • The camera must be loaded and running for the running time to go out.
  • Save and close each race when it finishes, or the board keeps showing the race that is open. FinishLynx marks the event the board is showing with an S to its left.
  • When results and running time go out on the same COM port, press Alt+S to stop the running time and show the results.
  • Don't use Dak-Extended.lss for this board. That script is for Daktronics LED video and message displays: see LED video displays.
  • If you also run a small race clock, give it its own scoreboard entry with its own script and serial port, for example Raceclock by Electro-Numerics.

FieldLynx on a Daktronics portable timer (TI-2021)

  1. In FieldLynx, go to Options | Preferences | Scoreboard tab, click New, then Configure, and set Metric to DakTI2021_met.lss, English to DakTI2021_eng.lss and Standings to DakTI2021_met.lss, with Code Set Single Byte.
  2. Under Communication, choose the COM port of the signal converter, Baud 19200, Parity None, 8 bits per character, 1 stop bit, Flow Control None.
  3. Restart FieldLynx and check the Status reads Running, then use Send Mark with an event open.
  4. There is no Lynx script for the non-standard 11-segment TI-2021: see Scoreboard plug-in and settings.

Every Daktronics setup, with its wiring drawings, is in Daktronics' Track & Field Interfaces for Scoreboards & Displays setup guide, and the latest version is on Daktronics' support site.

Related resources