Downloading, Installing & Moving to a New Computer
FinishLynx and every plug-in you own are separate downloads from the Software page, each with its own 12-character serial. Updating on the same computer is one installer; moving to a new computer means installing FinishLynx, then each plug-in, then setting the network up again.
Everything starts with your serials, so find them first.
How to fix it
Find your serial numbers
- On any computer that opens FinishLynx, go to Help | About.
- It lists the FinishLynx serial and every installed plug-in with its own serial.
- Write them all down or take a screenshot before you reinstall or move.
- No serials anywhere? See Lost serial numbers.
Update FinishLynx on the same computer
- Close FinishLynx.
- Download the latest FinishLynx from the Software page and run the installer.
- Enter your FinishLynx serial when asked. Name and Company are optional, so you can leave them blank.
- Install into the same Lynx folder as your existing copy,
C:\Lynx.- A second copy in another folder causes confusion later, and plug-ins only work from the same folder as the main program.
- Plug-ins that were already installed don't need reinstalling after an update.
Move FinishLynx to a new computer
- On the old computer, record the FinishLynx serial and every plug-in serial from Help | About.
- On the new computer, download FinishLynx from the Software page, install it into
C:\Lynxand enter the FinishLynx serial. - Install each plug-in (RadioLynx, Automatic Capture, LapTime and so on) with its own installer from the Plugins section, entering that plug-in's serial.
- Plug-in serials are tied to the FinishLynx serial: the first six digits must match. A plug-in won't activate on a copy of FinishLynx installed under a different serial.
- To keep your settings, copy
Lynx.cfg(software settings) andLynx.cdf(camera settings) fromC:\Lynxon the old computer intoC:\Lynxon the new one.- Without them, camera settings start at their defaults, so set the start sensor, capture method and scoreboard entries again.
- Camera upgrades (VDM, LuxBoost, HighRes) live in the camera, so they need no code on the new computer. See Upgrade code.
Set up the new or rebuilt computer
- Give the camera's Ethernet adapter a static IP address and set up file sharing with the Windows 11 networking guide (or the Windows 10 networking guide).
- If the camera won't boot on the new computer, it is nearly always this computer's setup. Work through FinishLynx not finding camera.
- Allow
C:\Lynx\Lynx.exethrough the firewall and turn Wi-Fi off while the camera boots - In File | Options | General set Hardware Type to Detect and Camera Network to the static address
- Allow
- If this computer will only evaluate races (no cameras), go to File | Options | General, set Hardware Type to None and restart FinishLynx. See Capture-and-read FinishLynx setup.
Common install questions
- Will my older camera work with the latest FinishLynx? Yes. Every camera, however old, works with the current FinishLynx, so don't install an older version. If a camera won't load and you have FinishLynx LITE, check which edition you have.
- Does FinishLynx run on a Mac? No. FinishLynx is Windows software: see Known limitations.
- The installer shows an error or won't start. See Installer errors.
- One computer is Windows 10 and the other Windows 11. Is that a problem? No, FinishLynx works the same on both. Only the static IP and file-sharing steps differ slightly, so follow the networking guide for each computer's Windows version.
- Can I install FinishLynx on a second computer? Yes. Install it on the evaluate computer, or on the new computer while the old one is still in use, with the same FinishLynx serial, then set the second one up as in Capture-and-read FinishLynx setup.
- What should our IT department set up? See Computer and IT readiness checklist.
If FinishLynx keeps asking for a serial after the install, see Keeps asking for a serial number.
Related resources
- Windows 11 networking guide — Guide · PDF
- Windows 10 networking guide — Guide · PDF