"All start sensors failed to arm"
"All start sensors failed to arm" pops up when you load an event from the schedule or create a new one. It means a start input FinishLynx expects to be live isn't set up or connected.
Almost every case support sees is a settings problem. The fix is to set both start tabs in Camera Settings to match how you start races, including the one you don't use.
How to fix it
Set both start tabs to match your start
- Open Camera Settings for the timer-enabled camera and set the two tabs for your start method
- RadioLynx (pistol or electronic gun): Inputs tab, Start Sensor = None; RadioLynx tab, Port = where the receiver is connected and Setup = Start Sensor (not None)
- Wired start with a pistol: Inputs tab = Closed; RadioLynx tab Port = Off
- Wired start with an electronic gun: Inputs tab = Open; RadioLynx tab Port = Off
- On the RadioLynx tab, pick the Port by what is plugged into the camera
- Short black antenna screwed onto the gold threaded RADIO LYNX connector (Vision camera with Internal RadioLynx): Internal
- External receiver with a round black plug in the RadioLynx connector: RadioLynx Port
- External receiver on a serial cable to the camera back: Camera Back
- Receiver on the connection box's serial port and 12 V output (an EtherLynx 2000, for example): Connection Box
- Uncheck Transmitter sends periodic status at the bottom of the RadioLynx tab
- Click OK, then load the event again. The pop-up should not appear
- Test: press the signal button on the transmitter (or tap the wired sensor) and check that FinishLynx receives the start
The tabs are described on the manual's Camera Settings page, and Configure FinishLynx for RadioLynx Start Signals shows the RadioLynx setup.
If a wired start sensor still won't arm
With the Start Sensor set to Closed, the camera is seeing an open circuit where it expects the sensor's closed circuit.
- Make sure the sensor is on the start cable and the cable is connected to the connection box or the camera
- Confirm the red light on the side of the sensor is lit
- Bypass the long start cable: plug the sensor straight into the connection box or the DB15-to-XLR cable
- If the error stays, the sensor, the connection box cable or the camera may be at fault: the Two-minute sensor or cable test narrows it down, and Lynx can take it from there
If RadioLynx still won't arm
- RadioLynx tab grayed out: the plug-in isn't installed on this computer. See RadioLynx port settings grayed out
- Pop-up gone but no starts come in: see RadioLynx not working
Check these
- The Inputs tab matches your start: Closed for the standard wired sensor, Open for a wired electronic gun, None if no wired start is used
- The RadioLynx tab Port is Off if you don't use RadioLynx
- With more than one timer-enabled camera, check the Inputs and RadioLynx tabs on every camera, not just one. A common cause is one camera set for wireless while the second is still set for a wired start
- On a new computer or after a reinstall, check these settings again. A fresh install doesn't carry over your old camera settings, so the Inputs tab and the RadioLynx Setup are back at their defaults
- Using manual starts only? Set the start sensor to None. Using image starts or TOD starts? Set it to Open to avoid arming errors
- Starting with a Gill Halo? See Gill Halo
If the scoreboard doesn't show 0:00 when the event opens
- Click Scoreboard | Options… and select the scoreboard
- Check Running Time is Normal, and in the Options menu next to it uncheck Send results if armed
- Unchecked, a running-time board shows 0:00 as soon as the event is armed. Check it only on a results board, such as a video board or ResulTV, to show the start list once the event is open
If races already ran with the error
Without an armed start, FinishLynx can only show time-of-day times (for example, finishers at 16 hours and some minutes).
- Open the event, click Event | Select Start…, choose the right start and click OK
- If the start never arrived, see Recover a race after a missed start
- Re-arming an event and then saving it also replaces its start, so use Select Start to put the right one back
Good to know
"Transmitter sends periodic status" makes FinishLynx check that the transmitter is in range when an event is armed. It needs the transmitter in "Son" mode (hold the 2nd button for 5 seconds to switch between Son and Sof).
Talk to Lynx Support
Tell the team what you’re seeing and what you’ve already tried. They’ll follow up by email or phone.