Recover a race after a missed start
FinishLynx records the image without a start, but until it has one it can only show time of day: it needs a start to turn image times into race times. If the start was missed, add one afterward with the first option below that fits.
How to fix it
RadioLynx: press Repeat on the transmitter
If the transmitter sent the start but FinishLynx didn't get it (for example, the camera was offline), Repeat recovers the original gun time.
- Bring the camera and FinishLynx back up.
- Press Repeat on the transmitter before the starter fires again.
- Repeat resends the transmitter's last signal, and RadioLynx signals carry a time stamp, so FinishLynx starts the clock from the original start time.
- If the starter has fired again since, Repeat resends that newer start instead.
- The transmitter keeps only its most recent start. FinishLynx can't read older starts from it, so on a long course where a start may not get through, press Repeat right after each start.
Apply a start FinishLynx received
Every start received since the camera booted is in the start list at the top left of the window, including the real gun after a false start.
- With the event still open, select the start in the start list.
- Click the Add Selected Start icon to the right of it.
- If the event was saved and reopened, click Event | Select Start… instead, choose the start closest to the race and click OK.
- The list holds the five most recent starts from when the event was created or reloaded, plus every start received or applied while it was open and capturable.
- If you re-armed the event and then saved it, the start was replaced. Choose the right one again with Event | Select Start….
- Check the times in the Results. If they're wrong, try another start in the list.
- If no start in the list is anywhere near the race, FinishLynx never received it: use one of the two options below.
You know the time of day the gun fired (TOD start)
This works while a timer-enabled camera is on, or in an event that was created while one was on.
- Open the event.
- Click Event | TOD start… and enter the time of day of the start.
- For full precision, use 4 digits after the decimal point.
You have a known time for one finisher (Image Start)
- Place the hash line on the torso of an athlete whose time you know, for example a hand time.
- Click Event | Image Start. That point becomes 0.0.
- Click Results | Filters…, check Offset, enter the athlete's known time and click OK.
- Re-evaluate that athlete, then evaluate the rest of the field. Their times come from the image relative to that athlete.
- If your rules call for the 0.24 s hand-timing adjustment, add it once, to the offset. Every other time is a difference from that athlete, so it carries to everyone. Don't add it again to each runner.
Keep the meet running until the start is fixed
- Use the wired start cable as a backup to RadioLynx or an electronic gun.
- With a pistol, use the white normally closed wired sensor (not the red RadioLynx sensor) and set the start sensor on the Camera Settings | Inputs tab to Closed.
- With an electronic gun, connect the start cable to the gun cable's Start Output and set the Inputs tab to Open.
- Or use manual starts: set the Inputs tab start sensor to None, then for each race create the event, click Event | Manual Start and press the Space Bar when the gun fires.
- If you're starting from a watch, type its running time as the offset first. Manual starts are only accurate to 1/10 of a second.
Then find the cause
- RadioLynx: RadioLynx not working
- Wired start sensor: Two-minute sensor or cable test
- Electronic gun: Using wireless RadioLynx
- "Start sensors failed to arm" when you open an event: "All start sensors failed to arm"
- Results still in time of day, 24-hour times or a negative time: Times are in TOD
The manual's Apply Starts page and the video Configure Starts, Re-Arm Events, & Apply Times show the start list and Select Start in action.
Good to know
A missed start can be added afterward, but missed image can't: if capture was off when athletes crossed, those finishes weren't recorded. See When to capture.
Related resources
- Configure Starts, Re-Arm Events, & Apply Times — Video · YouTube