Align the camera on the finish line
An EtherLynx camera sees a very thin slice of the world, and that slice has to be the finish line. Aligning means putting the camera in the plane of the finish line, levelling it, pointing it at the front of the white line, and then setting zoom, focus and iris.
When it is right, images have a white background with black lane lines, because the background of a photo-finish image is the finish line repeated thousands of times. A camera that isn't aligned gives inaccurate times, so align before every meet and don't skip steps.
How to fix it
Before you start
- The camera has loaded: it is listed in the Hardware Control window and the green status bar has finished. If FinishLynx shows "Error Aligning a Camera", no camera has loaded yet; see the FAQ under Common error messages
- The finish line is white, with black squares where each lane line crosses it. If they are missing, put small pieces of flat black (matte) tape on the lane lines. Don't use shiny plastic tape, which can look white in sun. The manual's Finish Line Prep page shows how it should look
- An assistant who can walk or run through the finish line, and for the first setup a string at least as long as the track is wide, plus a plumb bob
Mount the camera in the plane of the finish line
- Set the tripod up on the extension of the finish line, usually on the infield and about 10 feet (3 m) back from lane 1. 8 feet is the practical minimum
- A pole, or a clamp on something that doesn't vibrate, also works. See the manual's Camera Mounting page
- Stand the tripod on the ground, not on a table: a table wobbles and moves the camera off the line
- Height: 7-15 feet, angled down at about 45 degrees to the nearest edge of the track. Higher means less blocking of outer lanes, but go higher only with a heavy, weighted tripod or a pole that won't sway in wind
- Tie the string to the screw on top of the tripod head and have your assistant hold it taut over the middle of the finish line on the far side of the track. Hang the plumb bob over the middle of the finish line on the near side
- Move the tripod left or right until the string touches the plumb line. The tripod is now in the plane of the finish line
- Extend the tripod to its working height now. Raising the head tube after aligning moves the camera off the line
- In any wind, weigh the tripod down: see Tripod blows over or shifts in wind
Level the camera
- Fit the geared head (or Remote Positioner) and click the camera's mounting plate into place. See Camera or positioner won't mount securely if it won't lock
- With the lens facing the finish line, adjust the tripod legs until the tripod's bubbles are centered
- The camera's swivel (rotation) must be level. Use a standard level on the camera, or, on a Vision-series camera with the Level Indicator option, adjust swivel until the level icon in the Hardware Control window is green (within 0.2 degrees, ideally 0.0). Watch the Electronic Level Indicator video
- Set a starting tilt of about 45 degrees down toward the track
Start alignment mode in the Hardware Control window
- Start FinishLynx and wait for the camera to load
- Click the camera in the camera list so its row is highlighted. With two cameras, align one at a time
- Vision-series cameras (Vision, Vision PRO, Vision PRO X): click the 2-D align icon, the red stop sign with "2D" in it at the top left of the Hardware Control window. It turns green and shows a live picture with a green vertical line
- The Manually Align a FinishLynx Vision Camera video shows the whole process
- Older cameras (EtherLynx 2000, PRO, Fusion): click the 1-D align icon to start Line Scan mode. The picture won't look like normal video; you are aiming for a white background with black lane lines. See How to Align an EtherLynx Photo-Finish Camera on the Finish Line
- If the view is black, take the lens cap off and open the iris: see Image is fully dark or black
- Use the + and − buttons to zoom the view. Ctrl- or Shift-click them (Smart Zoom) to fit the whole image height in the window
Put the finish line in the picture
- Tilt: have your assistant run through the finish line in lane 1 and in the outside lane. Tilt until lane 1 shows at least from the knees or waist up and the top of the head shows in the outside lane, without a lot of empty space above
- Pan: turn the camera left or right until the green line sits on the front half of the white finish line, near its front edge, not in front of the line or behind it
- On a windy day or soft ground, put the green line down the middle of the white line instead, so the camera can move a little and still stay on the white
- If the far lanes run off the white line while the near lanes are on it, the camera is off swivel: level it again
- With a tripod head, use its Tilt, Pan and Swivel knobs. With a Remote Positioner, use the controls in the next section
Using a Remote Positioner
- Connect the positioner cable from the camera's Remote Control port to either port on the positioner, and the lens cable to the other positioner port
- The positioner only moves while the camera is in alignment mode. Before you start, click the center-positioner icon so it starts from the middle of its range; the status bar shows the progress
- The arrows on the right of the Hardware Control window are Swivel clockwise and counter-clockwise, Tilt up and down, and Pan left and right. One click makes a very small move; holding the button keeps it moving for about 2 seconds
- For bigger steps, hold a key while you click: Shift-click moves further than a plain click, Ctrl-click further again, Ctrl+Shift-click the most
- If the positioner can't reach the line, move the tripod by hand to get close, then fine-tune with the arrows
- During the meet you can nudge the positioner to correct for wind or tripod movement. The Remote Positioner and EasyAlign video and the EasyAlign demo show the positioner, zoom and focus controls
Set zoom, focus and iris
- Zoom so the view is just wide enough to show everything you need to read in every lane. Remote lens: Zoom In and Zoom Out. Manual lens: the zoom ring. The 2.8-10mm lens is varifocal, so refocus after every zoom change
- Focus until the Focus Helper number above the alignment view is as high as you can get it. Right-click and drag a box over the lanes to focus on that area
- Remote lens: Focus Far and Focus Near. Manual lens: start with the focus ring on the distance to a point about a third of the way across the track, then fine-tune
- Auto-Focus (FinishLynx 13.10 or later, remote-control lens): in 2-D EasyAlign mode hold Ctrl + Shift and click Focus Near or Focus Far. Press Esc to stop. See the Auto-Focus video
- With a C-mount lens, first check AEC and open the iris as far as you can without washing out the picture
- To keep focus as the light fades, focus with the iris wide open: on a Vision-series camera with Gain Method AGC, check AEC in 2-D mode, open the iris fully, focus, then uncheck AEC
- Iris: with a remote-control lens let FinishLynx manage it. In Camera Settings | Parameters set Gain Method to AGC and check Auto Iris. With a manual lens, turn the iris ring until the gain sits around 40
- If it won't come sharp, see Image is blurry and can't focus
Confirm in 1-D Line Scan mode
- On a Vision-series camera, click the green 2-D icon to stop EasyAlign, then click the 1-D icon
- Have your assistant walk through the line. Across every lane you should see a white background with black lane lines
- Dark background with white lines: the camera is in front of or behind the line, so pan again. White in some lanes only: the camera is off swivel, so level it again. More help: No white background after alignment
- Set the white balance while still in alignment mode: right-click and drag a box over a white area, then click the white balance button
Test before the meet
- In Camera Settings, Setup tab, check Image Orientation (Left for a camera on the infield), Identify By (Lane), the number of Lanes, and an Iris Type that matches your lens. For the other settings, see Starting camera settings
- Create a new event (File | New), turn capture on and capture your assistant running through the inside and outside lanes. Check the background is white, the lane lines black, and every lane readable and in focus
- Turn alignment mode off before racing starts. The alignment view can't be saved or used for timing
- Check again between sessions, after anyone bumps the tripod, and as the light changes
EasyAlign view slow or laggy
- The 2-D view's frame rate is a hidden setting, Hardware\Align2D\Rate. The Vision PRO X has its own 2-D rate setting (default 25) that overrides it
- How often FinishLynx checks for a new alignment image is Hardware\Ethernet\AlignResol, which may need to be increased over Wi-Fi
Guides and videos
- The Online Manual's Camera Alignment chapter covers each step, and the Camera Alignment Tools page the Focus Helper, Smart Zoom, Level Indicator, EVF and AEC
- The EtherLynx Vision Camera Setup QSG and the EtherLynx 2000+, Fusion, and Pro Camera QSG show the steps with pictures
- The Setup Basics training session covers alignment at about 33 minutes
Good to know
If the camera is far from the timing table, an Electronic ViewFinder makes aligning easier: check EVF in the Hardware Control window and watch the alignment view on a phone with the Lynx ViewFinder app (EVF WiFi & Lynx ViewFinder App QSG) or on a monitor on the camera's HDMI port. The A button on the camera back turns on alignment mode and the EVF right at the camera, and steps through the alignment views.
Related resources
- Manually Align a FinishLynx Vision Camera — Video · YouTube
- EtherLynx Vision Camera Setup QSG — Guide · PDF
- EtherLynx 2000+, Fusion, and Pro Camera QSG — Guide · PDF
- Setup Basics training session — Video · YouTube
- EVF WiFi & Lynx ViewFinder App QSG — Guide · PDF